[chan-capi-users] chan_capi, Q.SIG: ISDN1#30: CAPI INFO 0x34e4: Invalid information element contents
Rudolf E. Steiner
res-1 at communicate.at
Mon Jul 6 15:20:45 CEST 2009
Am 05.07.2009 10:31, schrieb Mario Goegel:
>> I try to send a call to a Q.SIG-Tenovis-System with
>> "Dial(CAPI/ISDN1/${EXTEN})":
[...]
>> I use a "Dialogic Diva V-PRI/E1-30 PCI v3".
[...]
> currently you do not have enabled the QSIG specific part of chan_capi.
> So there may be a basic problem with your connection.
> With your dial you don't send any callerid, tried to set one?
Yes (same problem).
> Can you receive calls from four Tenovis switch? If so, can you provide a
> trace of such a call?
Yes.
Here the trace:
----- begin -----
CAPI: ApplId=0x0002 Command=0x02 SubCommand=0x82 MsgNum=0x05e1
NCCI=0x00000801
CONNECT_IND ID=002 #0x05e1 LEN=0052
Controller/PLCI/NCCI = 0x801
CIPValue = 0x1
CalledPartyNumber = <80>946123456789
CallingPartyNumber = <21 81>5023410
CalledPartySubaddress = default
CallingPartySubaddress = default
BC = <80 90 a3>
LLC = default
HLC = default
AdditionalInfo
BChannelinformation = default
Keypadfacility = default
Useruserdata = default
Facilitydataarray = default
SendingComplete = default
-- CONNECT_IND
(PLCI=0x801,DID=946123456789,CID=5023410,CIP=0x1,CONTROLLER=0x1)
> ISDN1#30: msn='*' DNID='946123456789' DID
== ISDN1#30: setting format alaw - 0x8 (alaw)VOCODER
== ISDN1#30: Incoming call '05023410' -> '946123456789'
CAPI: ApplId=0x0002 Command=0xff SubCommand=0x82 MsgNum=0x05e2
NCCI=0x00000801
MANUFACTURER_IND ID=002 #0x05e2 LEN=0037
Controller/PLCI/NCCI = 0x801
ManuID = 0x44444944
Class = 0x912000a
Function = 0x80e0200
ManuData = default
MANUFACTURER_RESP ID=002 #0x05e2 LEN=0016
Controller/PLCI/NCCI = 0x801
ManuID = 0x44444944
Class = 0x0
Function = 0x0
ManuData = default
-- ISDN1#30: Ignored MANUFACTURER_IND Id=0x44444944
CAPI: ApplId=0x0002 Command=0x08 SubCommand=0x82 MsgNum=0x05e3
NCCI=0x00000801
INFO_IND ID=002 #0x05e3 LEN=0017
Controller/PLCI/NCCI = 0x801
InfoNumber = 0x1e
InfoElement = <a5 90>
INFO_RESP ID=002 #0x05e3 LEN=0012
Controller/PLCI/NCCI = 0x801
-- ISDN1#30: info element PI a5 90
> ISDN1#30: Unknown progress description 90
CAPI: ApplId=0x0002 Command=0x08 SubCommand=0x82 MsgNum=0x05e4
NCCI=0x00000801
INFO_IND ID=002 #0x05e4 LEN=0028
Controller/PLCI/NCCI = 0x801
InfoNumber = 0x70
InfoElement = <80>946123456789
INFO_RESP ID=002 #0x05e4 LEN=0012
Controller/PLCI/NCCI = 0x801
-- ISDN1#30: info element CALLED PARTY NUMBER
-- ISDN1#30: Updated channel name: CAPI/ISDN1#30/946123456789-13
-- ISDN1#30: CAPI/ISDN1#30/946123456789-13: 946123456789 matches in
context isdn-in
== Started pbx on channel CAPI/ISDN1#30/946123456789-13
CAPI: ApplId=0x0002 Command=0x08 SubCommand=0x82 MsgNum=0x05e5
NCCI=0x00000801
INFO_IND ID=002 #0x05e5 LEN=0018
Controller/PLCI/NCCI = 0x801
InfoNumber = 0x18
InfoElement = <a1 83 81>
INFO_RESP ID=002 #0x05e5 LEN=0012
Controller/PLCI/NCCI = 0x801
-- ISDN1#30: info element CHANNEL IDENTIFICATION a1
CAPI: ApplId=0x0002 Command=0x08 SubCommand=0x82 MsgNum=0x05e6
NCCI=0x00000801
INFO_IND ID=002 #0x05e6 LEN=0015
Controller/PLCI/NCCI = 0x801
InfoNumber = 0x8005
InfoElement = default
INFO_RESP ID=002 #0x05e6 LEN=0012
Controller/PLCI/NCCI = 0x801
-- ISDN1#30: info element SETUP
== ISDN1#30: pbx already started on channel CAPI/ISDN1#30/946123456789-13
> chan_capi devicestate requested for ISDN1#30/946123456789 is
'Ringing'
-- Executing Answer("CAPI/ISDN1#30/946123456789-13", "") in new
stack
== ISDN1#30: Answering for 946123456789
CONNECT_RESP ID=002 #0x05e1 LEN=0054
Controller/PLCI/NCCI = 0x801
Reject = 0x0
BProtocol
B1protocol = 0x1f
B2protocol = 0x1
B3protocol = 0x0
B1configuration = <08 04 03 00 a0 00>
B2configuration = default
B3configuration = default
GlobalConfiguration = default
ConnectedNumber = <01 80>946123456789
ConnectedSubaddress = default
LLC = default
AdditionalInfo
BChannelinformation = default
Keypadfacility = default
Useruserdata = default
Facilitydataarray = default
SendingComplete = default
-- Executing Hangup("CAPI/ISDN1#30/946123456789-13", "") in new stack
== Spawn extension (isdn-in, 946123456789, 2) exited non-zero on
'CAPI/ISDN1#30/946123456789-13'
== ISDN1#30: CAPI Hangingup for PLCI=0x801 in state 6
-- ISDN1#30: activehangingup (cause=16) for PLCI=0x801
DISCONNECT_REQ ID=002 #0x0529 LEN=0013
Controller/PLCI/NCCI = 0x801
AdditionalInfo = default
> chan_capi devicestate requested for ISDN1#30/946123456789 is
'Not in use'
> chan_capi devicestate requested for ISDN1#30/946123456789 is
'Not in use'
> chan_capi devicestate requested for ISDN1#30/946123456789 is
'Not in use'
CAPI: ApplId=0x0002 Command=0x04 SubCommand=0x81 MsgNum=0x0529
NCCI=0x00000801
DISCONNECT_CONF ID=002 #0x0529 LEN=0014
Controller/PLCI/NCCI = 0x801
Info = 0x0
CAPI: ApplId=0x0002 Command=0x08 SubCommand=0x82 MsgNum=0x05e7
NCCI=0x00000801
INFO_IND ID=002 #0x05e7 LEN=0017
Controller/PLCI/NCCI = 0x801
InfoNumber = 0x8
InfoElement = <81 90>
INFO_RESP ID=002 #0x05e7 LEN=0012
Controller/PLCI/NCCI = 0x801
-- ISDN1#30: info element CAUSE 81 90
CAPI: ApplId=0x0002 Command=0x08 SubCommand=0x82 MsgNum=0x05e8
NCCI=0x00000801
INFO_IND ID=002 #0x05e8 LEN=0015
Controller/PLCI/NCCI = 0x801
InfoNumber = 0x804d
InfoElement = default
INFO_RESP ID=002 #0x05e8 LEN=0012
Controller/PLCI/NCCI = 0x801
-- ISDN1#30: info element RELEASE
CAPI: ApplId=0x0002 Command=0x04 SubCommand=0x82 MsgNum=0x05ea
NCCI=0x00000801
DISCONNECT_IND ID=002 #0x05ea LEN=0014
Controller/PLCI/NCCI = 0x801
Reason = 0x3490
DISCONNECT_RESP ID=002 #0x05ea LEN=0012
Controller/PLCI/NCCI = 0x801
> ISDN1#30: CAPI INFO 0x3490: Normal call clearing
== ISDN1#30: Interface cleanup PLCI=0x801
----- end -----
> Maybe there are wrong settings in your diva configuration...
> Do you have some informations about the Tenovis config?
Only, that it uses ISO-Q.SIG an it's NT (we are TE).
--
nemox.net
info at nemox.net
Rudolf E. Steiner
r.steiner at nemox.net
More information about the Chan-capi-users
mailing list